How to replace the MacBook Pro 13 ” 2009 DC Input Card?

Isn’t there power to your Macbook computer? then replace the DC Input Card. I will help you on this topic. You need to buy this product. MacBook Pro Unibody 13″ and 15″ MagSafe DC-In Board
ATTENTION

All responsibilities are over you. If you make a mistake while you fixing, your device can be break down or maybe you can't use it anymore. Be careful when you trying to fix devices.

60-180 Min

Fixing Time

Hard

Fixing Level

SHARE
Share on facebook
Share on twitter
Share on linkedin
Share on reddit
Share on whatsapp
Share on email

Spudger, Phillips 00 Screwdriver, Y1 Tri-point Screwdriver

#1 Lower Case

Remove the 10 screws on the back of your macbook.

The screws shown in red are 3mm screws

The screws shown in yellow are 13.5 mm screws.

Attention ;  Please do not confuse them as we will put them back on while removing

#2 Lift Cover

Please slightly lift the back of the case we removed the screws

#3 Disconnect Battery

Using the flat end of the spudger, remove the battery connector from its slot on the motherboard.

#4 Fan

Use a spudger straight from the motherboard to remove the fan connector from its slot.

Be careful when doing these operations. It will be healthier if you remove the spudger from the bottom as shown in the picture.

#5 Fan Screws

 

Remove the three screws you see in the photos

  • One 6.5 mm Phillips.
  • 2. One 5.5 mm Phillips.
  • 3 One 4.5 mm Phillips.

#6 Removing the fan

Remove the fan as shown in the picture.

#7 Logic Board

Grasp the plastic pull-tab that is secured with the display data cable locked and rotate it towards the DC input side of the computer.

Make sure to pull the connector straight away and not straight up from its socket.

#8 Screen Fastening Screws

Unscrew the screws where the shield cable is located

lift the data cable leading to the display towards the top and pull it towards you

#9 Speaker Connector

Use the flat end of a spudger to pry the subwoofer and right speaker connector up off the logic board.

 

#10 Camera Cable Connector

Gently pull it towards you to disconnect the camera cable from the motherboard. in the direction of the optical drive.

This socket is metal and easily bent. Be sure to align the connector with its socket on the logic board before mating the two pieces.

#11  Optical drive, Hard Drive, and Trackpad Cable

Use the flat end of a spudger to remove the optical drive, hard drive, and trackpad cable connections from the motherboard.

#12 Keyboard Ribbon Cable 

 

You have to be very careful here. Use your fingernail or the tip of the spudger to flip up the cable retention flap on the ZIF socket for the keyboard ribbon cable.

Use your spudger to slide the keyboard ribbon cable out of its socket.

#13 keyboard backlight ribbon cable 

Remove the light strip for the keyboard as shown in the photo.

#14 keyboard backlight ribbon cable

Use the tip of a spudger to flip up the cable retaining flap on the ZIF socket for the keyboard backlight ribbon cable.

Using the spudger, slide the keyboard backlight strip out of its slot and it will come out slightly.

#15  battery indicator cable

Lift the battery indicator cable from the main board

#16 Microphone

Lift it up slightly to remove the microphone connector, as it is sticky, it will come out immediately.

#17 Remove the following screws:

Five 3.1 mm Phillips.

Two 3.9 mm Phillips.

Two 7 mm Phillips from the DC-in board.

#18 Lift the battery out of the upper case.

One 5.5 mm Tri-point screw.

One 13.5 mm Tri-point screw.

Remove the following Tri-point screws securing the battery to the upper case:

Lift the battery out of the upper case.

#19 Lift the logic board

Lift the motherboard from its left edge and lift the ports until you clean the edge of the upper case.
Pull the main board from the side of the upper case and remove it, paying attention to the DC input board that can be installed.

Be careful not to rip out the fragile connector plug of the microphone assembly.

#20 Disconnect the DC-In board

Disconnect the DC-In board by pulling its connector away from the socket on the logic board.

 

In this way, you can make the Replacement of DC Input Card. For any problem, feel free to contact us. Have a nice day

0 0 vote
Article Rating
Subscribe
Notify of
guest
0 Comments
Inline Feedbacks
View all comments
ATTENTION

All responsibilities are over you. If you make a mistake while you fixing, your device can be break down or maybe you can't use it anymore. Be careful when you trying to fix devices.

0
Would love your thoughts, please comment.x
()
x

Login

You can acces your account, your notifications and your personal informations via your account.